Monitors

HL-DT-ST DVD GDR8162B DRIVER DOWNLOAD

You must have both a power connector from the power supply and a data cable properly connected to the drive. Make sure that there are no pins on the drive or on the mboard IDE headers that are bent over such that they’re not plugging into the data cable connectors. If it is possible for a data cable connector to plug into a IDE header either way, the striped side of the data cable must be next to the pin one end of the IDE header on all connections. Yes No I don’t have a dog. Net cannot verify the validity of the statements made on this site. Over a Month Ago Time Zone:

Uploader: Melmaran
Date Added: 10 October 2008
File Size: 30.86 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 31919
Price: Free* [*Free Regsitration Required]

The side of the data cable that has a colored stripe must be next to the 4 pin power socket. Try another data cable hp-dt-st in doubt. Yes No I don’t have a dog.

You don’t need to install drivers for it. It is common to un-intentionally damage IDE data cables, especially while removing them – the 80 wire ones are more likely to be damaged.

I have discovered I have the same model sitting around. The computer’s bios MUST be detecting the drive. It was made in August That model is relatively old. If you have a generic system and have the CD that came with the mboard, all the necessary drivers are on it. Thousands of users waiting to help!

The information on Computing. Net is the opinions of its users.

There are two rows of 3 pins on the back of the drive next to the pins for the IDE header. Another common thing is for the data cable to be separated from the connector contacts a bit after you have removed a cable – there should be no gap between the data cable and the connector – if there is press the cable against the connector to eliminate the gap.

Recent Drivers  REALTEK ALC655 6 CHANNEL AUDIO CODEC DRIVER DOWNLOAD

If you load drivers from the web, brand name system builders and mboard makers often DO NOT have the main chipset drivers listed in the downloads for your model – in that case you must go to the maker of the main chipset’s web site, get the hl-dt-zt, and load them.

Such opinions may not be accurate and they are to be used at your own risk. Use Question Form such as ” Why? Net and its accuracy. Do you have a hk-dt-st with the drive not being detected at all, or the drive is being detected but it is not working properly? Your drive is an IDE gdr8162.

If that doesn’t help, you may need to change a setting regarding drive detection – e. Over a Month Ago Time Zone: Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation. Would you use Snapchat filters on your dog?

[Solved] i need the drivers for Hl-dt-st dvd-rom gdrb instalation

It may NOT be able to recognize some types of “burned” disks that already have data on them. Make sure that there are no pins on the drive or on the mboard IDE headers that are bent over such that they’re not plugging into the data cable connectors.

It should either show up in the bios Setup, or if you have an old mboard, the model of the drive should show up on the first black screen while booting the computer. The jumper setting on the back of the drive must be set properly. Usually the thing that makes them un-usable first is the cheap sleeve bearings in the motor have worn to the point that so much friction is produced in the bearings that the motor can no longer spin at the minimum 1X legacy audio CD speed, or the motor evd spin at all.

Recent Drivers  OPTIARC DVD RW AD-5170A ATA DEVICE DRIVERS DOWNLOAD

Hl-dt-st dvd-rom gdr8162b

What the pins are for is stamped into the metal on top of the drive. Usually the pin one end of the IDE header on the drive is next to the power socket. What usually happens is the cable is ripped at either edge and the wires there are either damaged or severed, often right at a connector or under it’s cable clamp there, where it’s hard to see – if a wire is severed but it’s ends are touching, the connection is intermittent, rather than being reliable.

If it is possible for a data cable connector to plug into a IDE header either way, the striped side of the data cable must be next to the pin one end of the IDE header on all connections. There must be a jumper on one of those three pairs of pins. Your drive does not require an 80 wire data cable – a 40 wire one will do – but if it’s on the same data cable as a hard drive that requires an 80 wire data cable, you must use an 80 wire data cable to get the full max burst speed from the hard drive.

XP doesn’t have the drivers built in for most things that first came out after XP was first released, circaand it doesn’t have some of the drivers built in for things made before that.